Quick answer
The core macramé knots are the lark’s head (to mount cords), the half hitch (for lines and mesh), the square knot (for bands and bracelets) and the sliding knot (for adjustable closures). A gathering wrap binds a bundle of cords, and a simple rope belt uses a sliding closure. Learn the lark’s head and the square knot first, because most other knots build on them.
How macramé cords work
Most macramé pieces use two kinds of cord. Knotting cords are the working cords that move and form the knots. Carrying cords stay in place while the knotting cords are worked around them. In a square knot, for example, the knotting cords wrap around the carrying cords. Each knot is a sequence of over-and-under moves, so practise on a spare length first.
Lark’s head knot
The lark’s head mounts cords onto a ring, a dowel, a buckle or another cord. There are two ways to tie it.
Horizontal: Fold the cord in half and lay it over the bar, so a small loop sits above it. Pass both ends behind the bar, then through the loop from behind. Pull the ends down to tighten.
Vertical: Use this when you have only one loose cord to work with, such as in the middle of a project. Work the knotting cord over the carrying cord, make a loop around the carrier, and pass over the same knotting cord. Then go under and around the carrier in the other direction, and pull sideways to tighten. A simple way to remember it is over-under-over, then under-over-under.
Overhand knot
The overhand knot is the simplest knot, and it is used to finish a cord end. Make a loop, bring the end of the cord to the underside of the loop, and pull through until the knot is tight.
Half hitch: double and alternating
A double half hitch is worked over a filler cord that you hold in the direction you want the line to run, such as horizontal, vertical or diagonal. Take a working cord up, over and behind the filler, then pull the end through the loop. Repeat the same move right beside the first to make the second half hitch. Move to the next working cord and repeat across the row.
An alternating half hitch uses the cords themselves rather than a filler. Cords loop around one another in a cascading mesh. On each row, change which cords are active, so the pattern builds a diamond or net-like shape.
Half square knot and square knot
The half square knot is worked with two knotting cords and two carrying cords. The right knotting cord travels over the carrying cords and under the left knotting cord. The left knotting cord then travels over the other knotting cord, under the carrying cords, and up through the loop made by the right cord. Pull both knotting cords to tighten. Mirror the steps for a left half knot.
A square knot is two half knots in alternating directions: a right half knot, followed by a left half knot. A chain of square knots makes a flat band, used for bracelets and wall hangings.
Switch square knot
After one square knot, bring the knotting cords straight down. They become the new carrying cords. The old carrying cords move to the sides and become the knotting cords. Tie a square knot with the new set. The result is a criss-cross pattern. Working it in two colours makes a simple bracelet.
Gathering wrap knot
A gathering wrap binds a bundle of cords together, to hold them neatly before a finish. This is a general method, so test it on spare cord before you use it on a finished piece.
- Lay a separate working cord along the bundle, with its tail running along the bundle too.
- Wind the working cord tightly around the bundle and the tail, keeping each turn side by side.
- After enough turns, pass the working end through the last loop, pull the tail to draw the end under the wraps, and trim.
Sliding knot for an adjustable closure
A sliding knot lets a bracelet or necklace adjust in size. It works with cord 2 mm or thicker, such as satin cord, waxed cotton or paracord. A cord of about 50 to 75 cm is a common starting length for a bracelet, but test the length first.
- Overlap the two cord ends, with the left end on top of the right.
- Hold the crossover point between your finger and thumb. Wrap one end around your finger two or three times to make neat, side-by-side loops, then slide them off.
- Thread the same end back down through all the loops and out the other side. Pull it to form a small barrel around the other cord.
- Repeat with the other cord end, so you have two sliding knots facing each other.
- Test the slide, then trim the tails close. Melt synthetic ends with a lighter, and press them flat.
A simple rope belt with a sliding closure
A rope belt can use the same sliding knot as a closure. Work the cord around your waist with a few spare inches, and set the closure so the belt is comfortable. A belt sits against the body, so check that the closure holds and that the ends are sealed before you wear it.
For cord choices, see the macramé cord guide. For a basic adjustable loop, see how to do a slip knot for beginners. For a square-knot weave in a bracelet, see the cobra knot guide. For an overview of knot crafts, see decorative knots and knot tying crafts.