What a loop knot does
A loop knot makes a loop at the end of a rope or line, or in the middle of it, so that something can be attached, hung, or tied off. Loops show up in most outdoor activities, from mooring a boat to rigging a tarp to landing a fish.
Loops are not all alike. Some hold their size under load, some slide to adjust, and some lock onto the line they are tied to. Picking the wrong type is a common mistake, and in climbing or rescue it can be a serious one.
Three types of loop
Fixed loops
A fixed loop keeps its size when it is loaded and does not slide along the rope. The bowline is the best-known example. Other fixed loops include the figure eight follow-through, the alpine butterfly, and the Yosemite bowline. Fixed loops are the usual choice when the loop has to hold its size, such as for a tie-in point or a mooring line.
Slip loops
A slip loop is formed so that the loop itself can slide along the standing part. That makes it quick to adjust, but the loop can also shrink under load. Slip loops have their uses, but they are generally avoided where a loop has to keep its size.
Non-slip loops
A non-slip loop is tied at the end of a line and locks onto the line with wraps. Anglers use it to attach a lure or fly while leaving the lure free to move. The non-slip mono loop is the common version, and its steps are in our guide to a loop knot that won’t slip.
Non-slip loops suit fishing line and light cord. They are not a substitute for a fixed loop on climbing rope or rigging.
Which loop for which job
Treat this as a starting point, not a rule. Check the rope, the load, and the guidance from your instructor or the rope maker before you rely on any loop.
- Climbing tie-in: the figure eight follow-through is a common choice. Learn it in person from a qualified instructor. See the figure eight follow-through guide.
- Mid-rope attachment, such as on a glacier or in a rig: the alpine butterfly knot is often used for this.
- A fixed loop at the end of a line, for boating or camp: the bowline is widely used on boats, and its variant the Yosemite bowline is discussed among climbers.
- Two loops in one rope: the bowline on a bight makes two fixed loops in one rope.
- Fishing a lure or fly: the non-slip loop lets the lure move freely.
Loop knots covered in this guide
- Bowline: a fixed loop, taught with the rabbit hole memory story. Widely used on boats and around camp.
- Yosemite bowline: a bowline with an extra finish. Climbers disagree about when it is the right choice.
- Figure eight follow-through: a common climbing tie-in knot, easy to check by eye.
- Alpine butterfly: a fixed loop tied in the middle of a rope, used in mountaineering and rigging.
- Bowline on a bight: two loops in one rope.
- Non-slip loop: a loop that locks onto fishing line, for lures and flies.
Loop knots and bends
A bend joins two ropes rather than making a loop at one end. Bends are chosen differently from loops:
- The sheet bend joins two lines of different thickness.
- The water knot joins flat webbing.
- The double fisherman’s knot joins two ropes of similar size, and is common in climbing and cordage.
A bend that works for one job may be a poor choice for another. Check each knot against the job before you tie it.
Checking a loop before you trust it
- Leave a tail. Short tails are a common reason a knot works loose. Use a length that suits the line.
- Dress the knot. Remove twists, lay each part flat, and set the knot by pulling on it.
- Compare with a reference. If the knot does not look like the diagram or the knot you were shown, untie it and start again.
- Inspect after loading. Check the knot after heavy loads or falls.
- Check the rope. A correctly tied knot cannot make up for a damaged rope.
Learning loops safely
Practice with a spare piece of rope before you use a knot for anything that matters. For climbing, rescue, or hauling, learn from a qualified instructor and have a partner check your work. This guide summarises knots. It does not replace hands-on instruction.