The square knot, also called the reef knot, is a flat binding knot made from two half knots tied in opposite directions. Most people learn it as the first step of tying shoelaces. It holds well enough for light, everyday jobs, such as tying up a parcel or closing a bag. It is not a knot to trust with heavy loads, to join two ropes, or for any job where a slip could cause an injury.
How to tie a square knot
- Cross the left end over the right end, then tuck it under.
- Cross the right end over the left end, then tuck it under. This second crossing goes in the opposite direction to the first.
- Pull the two long parts of the line in opposite directions until the knot sits snug.
Check the result. The two crossings should mirror each other, and the knot should lie flat and look even. If both crossings went the same way, you have tied a granny knot instead. The square knot vs. granny knot comparison shows the difference in more detail.
What the square knot is good for
A square knot suits light, low-stakes binding:
- Tying up a parcel or a bundle of light items with string or twine
- Closing a bag, sack or roll of fabric
- Tying the ends of a ribbon or gift string
- Finishing shoelaces, where it becomes the base of a bow
- Flat decorative work such as macramé, where it is a basic building block
- Reefing a sail. This is where the name “reef knot” comes from, since sailors used it to tie down part of a sail in strong wind.
The knot is quick, easy to learn and easy to undo, which is why it is so common for these jobs.
When not to use a square knot
Do not rely on a square knot in these cases:
- Joining two ropes end to end. It can spill or come undone, especially when the ropes differ in thickness or stiffness. For joining ropes, a sheet bend is the usual recommendation. The when not to use a square knot guide covers this in more depth.
- Heavy or shifting loads. Under heavy load it can jam, and it can capsize and pull apart.
- Safety-critical work. Climbing, lifting, towing, rescue and securing a vehicle load are all jobs where a failed knot can cause serious injury. Use methods taught in a proper course, with rated equipment.
Clifford Ashley’s The Ashley Book of Knots, a standard reference, is blunt about the square knot as a bend, and most knot references agree that it should not be used this way.
Binding knots that do the job better
Many binding jobs have a knot that suits them better:
- Bundles of sticks or firewood: a bundling knot with a loop and cinch.
- Round things such as poles, bags and cylinders: the constrictor knot, which grips harder as you pull.
- The neck of a sack: the Miller’s knot, a traditional sack knot.
- A roast: the butcher’s knot, which holds the shape of the meat while it cooks.
- A box with string: the parcel string knot shows how to wrap and finish it.
For cinching a load over a vehicle, the trucker’s hitch is a tension hitch rather than a binding knot. For road cargo, use rated tie-down equipment where you can.
Twine knots
“Twine knot” covers several different jobs, so pick the knot by the task:
- Tying off a bundle or parcel: a square knot, finished with a half hitch for security.
- Joining two lengths of twine: a sheet bend. It is more secure than a square knot, and it is often recommended for joining the ends of baler twine because the joint feeds through machinery more smoothly.
- Cooking: the butcher’s knot uses cotton butcher’s twine to hold a roast in shape.
Common mistakes
- Tying a granny by accident. This happens when you repeat the same crossing twice. The square knot vs. granny and thief knots comparison shows how to tell them apart.
- Using thin or slippery cord. Slippery cord is more likely to slide loose, so choose a cord that grips.
- Leaving it unfinished. Many knot references suggest adding a half hitch on top of a square knot for extra security.
Safety note
The knots in this guide suit light tasks. For climbing, lifting, rigging or any load that could injure someone if it failed, learn from a qualified instructor, use rated equipment, and test a knot before you rely on it.