Decorative Knots

Lanyard Knot and Fiador Knot: Step-by-Step Guides

Step-by-step guides to the lanyard knot, a diamond stopper for knives and keychains, and the fiador knot, the chin piece on horse rope halters.

On this page
  1. Quick answer
  2. Lanyard knot: materials and cord
  3. Lanyard knot: step-by-step
  4. Fiador knot: what it is and where it is used
  5. Fiador knot: step-by-step
  6. Practice tips and common mistakes

Quick answer

The lanyard knot is a diamond-shaped stopper used on knife lanyards, keychains and zipper pulls. The fiador knot is a loop knot used as the chin piece on horse rope halters and hackamores. They are different knots with different jobs. Both suit decoration and light use better than any load.

Lanyard knot: materials and cord

  • Paracord is the usual choice. Nylon holds the shape well.
  • Scissors and a lighter for the ends.
  • A loop or a core to start the knot around. The knot is often worked around a loop, such as a lanyard loop or a keyring.

Lanyard knot: step-by-step

The lanyard knot is built by weaving the working ends over and under one another in a set order, until a central diamond forms. The sequence is easier to follow with a labelled diagram or animation. If a step here does not match your diagram, trust the diagram and check each pass.

  1. Form and weave. Make an initial loop. Weave the working ends over and under each other, following the diamond sequence, until a central diamond starts to form.
  2. Centre the ends. Route the top and bottom-left ends around the structure, then feed them up through the middle of the knot.
  3. Cinch and dress. Pull all the working ends together gradually. Shape the knot into a clean, symmetrical diamond.
  4. Finish. Trim the tails, seal nylon ends with heat and check the shape from several angles.

Fiador knot: what it is and where it is used

The fiador knot, also called the Theodore knot, is a loop knot. On a horse, it forms the chin piece of a rope halter or a hackamore. In craft work, it is used for decoration.

Because it is part of horse tack, check a halter’s fit and material with an experienced horse person before you use it on a horse.

Fiador knot: step-by-step

The fiador is tied from a single continuous length of stiff cord. Nylon or a poly rope made for halters is common. The steps follow a set path, though the details differ by method.

  1. Find the middle and form the initial loops. Find the exact midpoint of the rope. Make the starting loops in the shape your method uses, such as an S-shape or an L-shape.
  2. Weave the strands. Cross the working ends over and under the loops in the order your diagram shows.
  3. Form the central ring. Pull the outer sides of the loops down through the central diamond-shaped opening.
  4. Tighten evenly. Pull the bottom loops, the noseband sections and the four loose ends one at a time. Work out the slack gradually until the four-stranded ring locks in place.

The knot needs careful over-and-under weaving before you tighten it, so take your time.

Practice tips and common mistakes

  • Practise on a spare length of cord before you use the real one.
  • Keep the first weave loose until the shape looks right. Tightening early makes the pattern hard to fix.
  • A lopsided diamond usually means a pass went the wrong way. Loosen the knot and check the passes in order.
  • Do not use a lanyard or a fiador to hold a load. These knots are decorative. Use a load-rated knot and fitting for any job that must hold weight.

For another stopper for the end of a lanyard, see the Matthew Walker knot guide. For a braided lanyard body, see the sennit braid guide. For an overview of knot crafts, see decorative knots and knot tying crafts.

The complete guide to decorative knots

Decorative Knots and Knot Tying Crafts: Paracord and Rope Projects
Read the guide

Keep exploring

Guides from other topics

All topics →