Knot Basics

Best Knots to Learn: A Beginner's Guide to Knot Tying

Learn the eight knots beginners need first: overhand, figure-eight, bowline, clove hitch, half hitches, taut-line, sheet bend, and square knot.

On this page
  1. The eight knots to learn first
  2. Match the knot to the job
  3. A practical learning order
  4. Safety for climbing, rescue, and rigging
  5. Frequently asked questions

Most people need only a handful of knots. Eight cover the majority of everyday jobs: stopping a rope end from slipping, making a fixed loop, tying off to a post, joining two ropes, and adjusting the tension on a guy line. This guide covers those eight, shows which job each one is for, and suggests an order for practicing them.

The eight knots to learn first

Overhand knot (stopper)

The overhand is the simplest knot. Make a loop, pass the working end under the standing part and up through the loop, then pull both ends to tighten. It keeps a rope end from slipping through a hole or a block, and it is the base for many other knots. It can jam under load, so for a bulkier stopper use a figure-eight. Full steps are in our overhand knot guide.

Figure-eight (stopper and loop)

Make a loop near the end of the rope, wrap the tail once around the standing part, and feed the tail back through the loop. The result looks like the number 8. As a stopper it is bulkier than the overhand and easier to inspect. The same shape tied in the middle of a rope gives a fixed loop, the figure-eight on a bight. Climbers use these knots, including the figure-eight follow-through, but climbing knots should be learned from a qualified instructor, not from an article.

Bowline (loop)

The bowline makes a fixed loop at the end of a rope that does not slip or tighten under load. A common way to remember it is the rabbit story: the rabbit comes up out of the hole, goes around the tree, and goes back down the hole. Form a small loop, pass the working end up through it, around the standing part, and back down through the loop. The bowline is widely described as easy to untie after it has been loaded. Practice it on a real anchor, not in the air. In climbing and rescue work, a bowline is often backed up with a stopper knot.

Clove hitch (hitch)

Wrap the rope around a post, cross over the first wrap, wrap again, and tuck the end under the last wrap. The clove hitch is quick to tie and holds well under steady tension. It is often used to start and finish a lashing. If the load will change direction or move, finish the line with two half hitches.

Two half hitches (hitch)

Pass the end around the post or ring, bring it over the standing part and through the loop, then repeat the same motion right beside the first hitch. Pull both tight against the object. A single half hitch can slip on its own, so the second one is what makes the tie reliable. The half hitch guide covers the variations.

Taut-line hitch (adjustable hitch)

Use this hitch to put tension on a guy line. Wrap the working end around the anchor, coil it twice around the standing line toward the anchor, add one more coil outside those two, and pass the end through the new loop. Tighten it, then slide the knot along the line to adjust the tension. It holds under load, but it can loosen if tension is lost, so check it after the line settles.

Sheet bend (bend)

Use a sheet bend to join two ropes, especially ropes of different thickness. Form a bight in the thicker rope, bring the thinner rope up through the bight, around behind both parts of the bight, and under its own standing part. Pull both standing ends to tighten. A double sheet bend adds an extra turn for security.

Square knot (bend)

The square knot joins two ropes of equal thickness. It is useful for light jobs, such as tying a package, but it is not a reliable choice for joining two load-bearing lines. The shape is easy to get wrong. If you cross the ends the same way twice, you tie a granny knot, which slips. Remember “left over right, right over left,” and check that each end lies parallel to its own standing part.

Match the knot to the job

Job Knot
Fixed loop at the end of a rope Bowline
Stop a rope end from slipping through a hole Overhand, or figure-eight for a bulkier stopper
Tie off to a post, rail, or ring Clove hitch or two half hitches
Adjustable tension on a guy line Taut-line hitch
Join two ropes of different thickness Sheet bend
Join two ropes of equal thickness for a light task Square knot

For a wider reference covering dozens of named knots, see types of knots.

A practical learning order

  1. Overhand knot. Learn it first, because the other knots use the same basic motions.
  2. Two half hitches. Finish a line on a post or ring.
  3. Clove hitch. A quick tie-off for lashings and temporary lines.
  4. Bowline. Practice the rabbit method on a real anchor until you can tie it without thinking.
  5. Figure-eight. Learn both the stopper and the loop.
  6. Sheet bend. Join two ropes of different thickness.
  7. Taut-line hitch. Practice sliding it and retensioning a line.
  8. Square knot. Learn to spot a granny knot before you use a square knot at all.

Practice with a rope you can afford to use up, and check each knot by pulling on it the way you would in use.

Safety for climbing, rescue, and rigging

Text and video are not enough for climbing, rescue, or rigging. These knots are used where a failure can cause serious injury. Learn them from a qualified instructor, check every knot before you rely on it, and keep loads well inside the rope’s rated limits.

Knots reduce a rope’s strength because the rope bends sharply at the knot. The amount varies by knot and by rope, so use the manufacturer’s ratings rather than general figures. Retire any rope that shows wear, cuts, heat damage, or chemical exposure.

Frequently asked questions

What are the 8 essential knots everyone should know?

The eight knots in this guide are the overhand, figure-eight, bowline, clove hitch, two half hitches, taut-line hitch, sheet bend, and square knot. Some lists swap in a trucker’s hitch for the square knot, because it is useful for tying down loads. Learn the eight first, then add others as you need them.

How do you tie a half hitch knot?

Wrap the end around the post, cross it over the standing part, and pass it through the loop you made. Pull tight. A single half hitch alone can slip, so tie a second one right beside it in the same direction and pull both tight. The half hitch guide has the full steps.

Keep exploring

Guides from other topics

All topics →