What a cobra knot is and what it is used for
The cobra knot is a weave made from a chain of square knots. It is also called the Solomon bar. The result is a flat, ridged band that suits paracord bracelets, lanyards and keychains.
It is a decorative weave, not a load-bearing one. Do not rely on a cobra-woven piece for climbing, towing or any job where a failure would matter.
Materials
- Paracord: Type III (550) nylon paracord is the common choice. Pick two or more colours if you want a contrast in the pattern.
- Release buckle (optional): A buckle lets you put the bracelet on and take it off. Without one, you finish with a loop or a keyring.
- Scissors
- A lighter for melting the ends of nylon
Melt nylon in a ventilated space, keep the flame away from hair and loose clothing, and keep a container of water nearby. Melted nylon is hot and can stick to skin.
Set up the core on a buckle
Fold a length of cord in half to find its middle. Attach the middle to one half of the buckle with a lark’s head knot (also called a cow hitch). Bring the cord down and thread the free ends through the other half of the buckle.
Adjust the distance between the buckle halves so the band will fit your wrist with a little room to spare. Make a short test with spare cord before you cut your real length, because the finished band is shorter than the cord you start with.
Tie the cobra stitches
The weave is built from two stitches, one on each side of the core. You tie the left stitch, then the right stitch, and keep alternating.
Left stitch
- Lay the left working cord across the core, making a small loop on the left.
- Bring the right working cord down over the tail of the left cord.
- Take the right cord behind the core, then up and through the loop on the left.
- Pull both working cords outward to tighten the stitch against the buckle.
Right stitch
Mirror the steps: lay the right working cord across the core to make a loop on the right, bring the left cord down over the right cord, take it behind the core and up through the loop on the right. Pull both cords to tighten.
Keep the weave even
- Use the bar. After each stitch, look for the raised horizontal bar on the outside edge of the last stitch. If the bar is on the left, start the next stitch with the right cord. If it is on the right, start with the left cord.
- Keep tension steady. Pull each stitch snug against the one before. Pulling one working cord harder than the other makes the band lean.
- Keep the core straight. If the core twists, the whole band will spiral. Straighten it as you go.
Finish and melt the ends
When the band is the right length, pull the last stitches tight and trim the working cords, leaving about a quarter inch (about 6 mm) of tail. Melt each cut end with the lighter so it seals, then press the molten tip flat against the weave with the side of a cool tool. Let it cool before you handle the band.
Common mistakes
- Two stitches on the same side in a row. The bar ends up in the wrong place and the pattern breaks. Undo the last stitch, check the bar and tie again.
- A twisted band. The core has turned during weaving. Undo a few stitches, straighten the core and re-tie.
- Loose stitches. Loose stitches sag and show gaps. Snug each one, but not so hard that the core bunches.
Variations
- King cobra: This version uses more cord to build a wider, heavier band on the same square-knot idea.
- No buckle: You can finish a band with a loop at one end instead of a buckle. Plan the loop before you start, so it is the right size.
If you want to practise the stitch on its own, see how to tie a cobra knot step by step. For another bracelet weave, see the fishtail paracord bracelet. For an overview of craft knots, see decorative knots and knot tying crafts.