Most tight knots come open if you take the load off first, open a small gap in the middle, and work the knot apart slowly. Forcing a knot usually makes it tighter, and it can damage the rope. Use the methods below in order, and cut the knot only as a last resort.
Before you start
- Remove the load. Ease the tension so the strands can move. A knot under load grips hard.
- Identify the rope. Natural fibers such as cotton, hemp, and jute respond differently from synthetic cord. Soaking helps natural fiber much more than synthetic.
- Identify the knot. Knowing whether you have a hitch, a bend, or a stopper tells you which arm to work. Our easiest knots to untie guide lists the knots that jam most.
Method 1: push one arm through the knot
Most knots have two arms, which are the loose ends that lead out of the knot. Grip one arm and twist it several times in one direction. Then push a short section of it through the center of the knot, starting as close to the knot as you can, because that gives you the most leverage. Pull the pushed section out the other side, and wiggle it side to side if it sticks. The knot should loosen as you pull.
If the arm will not go through, twist it a few more times in the same direction and try again.
Method 2: open a gap with a pointed tool
Use a narrow tool with a point that is not sharp: a needle, a pick, a bamboo skewer, the tines of a plastic comb, or a marlinspike. Work it into the center of the knot and wiggle it back and forth to open a gap. Then pull one part of the knot to see whether it opens. If it does not, leave the tool in place, wiggle a little more, or swap in a slightly wider tool and try again.
Method 3: grip and work with pliers
Hold one side of the knot’s body, not its arms, with needle-nosed pliers, forceps, or a marlinspike. Hold the other side with your other hand or a second pair of pliers. Tug gently, alternating pulls, so the strands shift. When the knot starts to give, pull it apart by hand. Do not yank it. Too much force can break the fibers or distort the rope.
Method 4: soak natural fibers
For cotton, hemp, jute, and similar natural fibers, soak the knot in water for about ten minutes, then try again. If it is still tight, soak it for another ten minutes. Synthetic cords respond much less to soaking, so move on to the other methods.
Shoelaces
Start with a pick at the loosest part of the bow, usually where the loops cross. Pry gently until you can pull the loops apart. Then tie the bow again with a method that stays tied. Our shoelace knots guide covers the options.
When to cut, and what to avoid
Cutting is a reasonable choice when the rope is cheap or short, the rope is no longer needed, and the methods above have not worked. Cut one arm close to the knot with a sharp blade, and keep your hands and body clear of the blade. Keep as much rope as you can.
Avoid these methods:
- Biting the knot. Your teeth can crack, and the rope can be damaged.
- Hammering or tapping the knot against a hard surface. Debris can fly into your eyes, and the rope can be damaged.
- Heat or flame on synthetic rope. It can melt, burn you, and weaken the fibers.
- Forcing the knot. Heavy force can weaken or break the rope, and the damage may not show.
Ropes that carry loads
For climbing, rescue, rigging, or any rope that holds a load, do not keep using a rope that was damaged or overheated while you untied a knot. Inspect it closely for flat spots, fuzzy or glazed fibers, and soft spots. If you have any doubt about it, retire the rope.
Prevent tight knots next time
- Take the load off as soon as you can. A knot that has carried a load tightens.
- Dress the knot before loading it. Arrange the strands so they lie neatly before you tighten the knot.
- Leave a tail. A tail of a few inches gives you something to grab.
- Choose a quick-release knot if you need to undo the knot often. See our easiest knots to untie guide.
Frequently asked questions
Can I use oil or WD-40 on a tight knot?
Some lubricants can affect rope fibers, and not every product suits every rope. Check the rope maker’s advice before you use oil or a spray. If you are unsure, use the mechanical methods above first.
Is cutting always okay?
For cheap, expendable rope, usually yes. For rope that holds a load, think first. A cut leaves you with a shorter line, and a damaged rope should be replaced rather than trusted.
Why does a knot get tighter when I pull on it?
The load presses the strands together, and friction holds them in place. Taking the load off lets the strands move. Our how knots work guide explains why knots hold.