Braided line is thin and slick, so anglers often tie a monofilament or fluorocarbon leader to it. The leader adds abrasion resistance and is harder for fish to see in clear water. The connection between the two has to slide through your rod guides and hold under load. Below are the knots anglers reach for most, plus a blood knot for lines of similar size.
Quick comparison
| Knot | Best for | Profile | Learning curve |
|---|---|---|---|
| FG | Strong, slim connection | Slimmest | Steep |
| Double uni | Easy connection on the water | Bulkier | Gentle |
| Albright | Fast connection, lines of different thickness | Medium | Moderate |
| Alberto | Slim connection to fluorocarbon | Slim | Moderate |
| Blood knot | Lines of similar thickness | Medium | Moderate |
FG knot
The FG is often ranked the slimmest and strongest braid-to-leader connection. The leader is wrapped around tensioned braid in tight, neat coils, then locked with half hitches. The coils have to be tight and even, and the braid has to stay under tension the whole time.
- Put firm tension on the braid. Many anglers wrap the braid around a finger or hold it with the rod.
- Lay the leader across the braid and wrap it back and forth, about 16 to 20 times, in tight coils.
- Lock the coils with a few half hitches tied with the braid.
- Pull firmly so the braid bites into the leader.
- Trim the leader tag close, then trim the braid tag.
Because the wrap pattern is hard to describe in words, watch a slow demonstration before you try it.
Double uni knot
The double uni is two uni knots, one on each line, slid together. It is easier to learn than the FG and works well on the water.
- Overlap the braid and leader by about 6 inches, with the tag ends pointing in opposite directions.
- Form a uni on the leader around both lines, wrapping about 4 to 5 times.
- Form a uni on the braid around both lines. Braid is slick, so use more wraps, about 6 to 8.
- Wet both knots and pull the main lines apart so the two knots slide together.
- Trim both tag ends.
Albright knot
The Albright is quick to tie and works well when the two lines are very different in thickness.
- Form a loop in the leader.
- Pass the braid tag end up through the loop.
- Wrap the braid around the doubled leader about 8 to 12 times.
- Route the braid tag back out through the loop on the same side it came in.
- Wet the knot and pull tight, then trim.
Alberto knot
The Alberto is a slim connection that many anglers use to join braid to fluorocarbon.
- Form a loop in the leader line.
- Pass the braid through the loop, then wrap it down the leader about 7 times.
- Reverse and wrap back up the leader about 6 to 7 times, over the first wraps.
- Pass the braid tag back through the loop the same way it entered.
- Wet the knot, pull the two ends to cinch it, and trim.
Blood knot for braid to mono
The blood knot works best when the two lines are close in thickness. It can struggle to cinch when the difference is large, so it is a better fit for mono-to-mono or lines of similar size than for a thick braid and a thin leader.
- Overlap the two lines by about 6 inches, with the tag ends pointing in opposite directions.
- Wrap one tag end around the other line 5 to 7 times, then bring it back through the gap between the two lines.
- Wrap the other tag end around the first line 5 to 7 times, working in the opposite direction.
- Pass the second tag back through the same gap, going the other way.
- Wet the knot and cinch the two main lines slowly until the coils lock together. Trim both tags.
Other braid-to-leader knots
You may see the GT knot described as the strongest braid-to-mono connection. Strength claims for it vary widely between sources, so check a reliable step-by-step guide and test it before you rely on it.
Common mistakes
- Too little tension on the braid during an FG, so the coils loosen.
- Dry cinching. Wet the knot first to reduce friction.
- Uneven pulls. Pull the two main lines in opposite directions, not one line only.
- Skipping the test. Give the finished knot a firm tug. If anything slides, retie it.
Which one should you use?
- For the slimmest and strongest connection, and you have time to practice: the FG.
- For something quick on the water: the double uni or Albright.
- For lines of very different thickness: the Albright or Alberto.
- For lines of similar thickness: the blood knot.
If you are joining two lines that are both mono or fluorocarbon, see knots to join two fishing lines together. For the broader picture of braid knots, read fishing knots for braided line. If you need a more general answer about which knot goes between a leader and a main line, see the best knot to tie a leader to a main line.