What an eye splice is
An eye splice is a permanent loop made at the end of a rope. The rope’s own strands are buried back into the rope, so the loop does not depend on a knot. Splices usually keep more of the rope’s strength than a knot does, and they lie flatter and slide more easily through hardware. For the strength comparison, see is a splice stronger than a knot.
This guide covers double-braid rope, which has a braided core inside a braided cover. The core carries most of the load, and the cover protects it.
Before you start
- Read the rope maker’s splicing instructions. Bury lengths and tapers depend on the rope. The steps below are a general outline, and if they disagree with the maker’s chart, follow the chart.
- Confirm the rope type. Make sure it is braided, not three-strand. The method is different.
- Work in a clean, quiet space. Small mistakes are easy to make when you are rushed.
Tools you will need
- A fid: a tapered rod that feeds the core through the cover. Choose one sized for the rope.
- An awl: a sharp tool that opens the cover without cutting the core.
- Tape: to hold the ends and keep the strands in order.
- A marker: to mark the splice points.
- Scissors or a knife: for a clean finish.
Step-by-step eye splice in double-braid rope
- Choose the eye size and mark. Decide how big the loop should be. Measure from the rope end the length the splice needs, and mark the cover at the points where the core will go in and come out. Use the maker’s chart for the distances.
- Tape the end. Wrap tape around the end so the cover does not fray while you work.
- Open the cover. At the marked point, use the awl to open the cover without cutting the braid. Pull the core out of the cover from the end.
- Form the eye. Bring the rope back on itself to the loop size you marked, so the core end lies alongside the standing part.
- Bury the core. Use the fid to feed the core into the cover of the standing part, in the direction the maker’s chart specifies. Bury it for the length on the chart, and make sure it passes the crossover mark.
- Taper the core. As the core goes in, remove a few strands from it so the splice tapers smoothly and does not form a bulge.
- Milk the cover. Work the cover along the splice so the core disappears inside, and the diameter stays even. Push out any bumps, and keep the cover under light, steady tension while you do.
- Trim and finish. Cut the loose cover ends close, leaving the tail length the chart calls for. Add whipping or tape if the maker specifies it.
- Set the splice. Load it gently and steadily, not with a jerk, so the strands settle into place.
Be patient with the milking. Too little leaves the splice bulky and weak. Too much can force the core out of position.
Checking the finished splice
Look at the splice before you use it:
- The diameter is even along the splice, with no lumps or dips.
- No core shows through the cover.
- The eye is the size you planned.
- The cover does not slide over the core when you move it.
Then set the splice with a moderate, steady load and check it again. If the rope slides through the splice or the core shifts, stop and recheck the bury lengths. A splice that moves is not ready.
Eye splice vs knot
A well-made eye splice usually keeps more of the rope’s strength than a knotted loop does. Knots bend and compress the fibers, and that uneven loading cuts strength. A splice takes the load through the rope’s own structure. Quality still matters, because a poor splice can be weaker than expected. See is a splice stronger than a knot for the details.
Common mistakes
- Cutting into the core. Open the cover with the awl, not a knife.
- Burying too little. Follow the chart for the bury length.
- No taper. A blunt core makes a bulge and a stiff splice.
- Milking too hard. Forcing the cover can pull the core out of place.
- Setting with a jerk. Load the splice steadily. A sudden jerk can damage freshly buried fibers.
Other eye types
A Flemish eye is a neat loop that is most often associated with three-strand rope. It is made differently from the braided eye splice described here. This article covers braided rope only.
Diamond braid and paracord both look braided, but they are different products with different constructions and ratings. Do not assume one can replace the other. Check the spec sheet.
Wire rope splicing uses different tools and methods, and it is outside the scope of this guide.
Safety for loaded lines
A badly made splice can slip or fail. For lifting, rigging, towing, climbing or any load that matters, use the maker’s splicing data, and get trained guidance before you rely on the splice. For the working-load side of the picture, see rope strength, breaking strength and working load limit. For finishing the end after the splice, see how to finish rope ends.